Modifying the Strength of Soft Soils via Heating and Cement Grouting Method

Shareef, Ali H.; Al- Neami, Mohammed A.; Rahil, Falah H.

doi:10.30684/etj.2023.143018.1556

	Modifying the Strength of Soft Soils via Heating and Cement Grouting Method
Engineering and Technology Journal
Volume 42, Issue 5, May 2024, Pages 458-470 PDF (1.63 M)
Document Type: Research Paper
DOI: 10.30684/etj.2023.143018.1556
Authors
Ali H. Shareef^* ; Mohammed A. Al- Neami; Falah H. Rahil
Civil Engineering Dept., University of Technology-Iraq, Alsina’a street, 10066 Baghdad, Iraq.
Abstract
Soft clayey soils present geotechnical engineering challenges with significant stability and settlement. Various methods are employed to enhance the geotechnical properties of these soils. Heating and grouting are the methods used to improve such soil. A new heating and cement grouting system using gas as a source of heating through boreholes and Portland cement for grouting was designed and manufactured to enhance the soft soil. Different parameters were investigated, including the shear strength and the angle of internal friction, as well as the water/cement ratio, W/C (0.5, 0.75, 1, 1.25, 1.5, and 1.75), and the period of curing (3, 14, and 28 days). The results showed the shear strength and angle of internal friction increased from 14 to 300 kPa and 0 to 50 degrees, respectively. If only the heating system is running, the strength and behavior of the soil will improve via heated and cement grouting with a water/cement ratio. If the w/c ratio increases from 0 to 1.25, the ultimate bearing capacity ratio (qu treated/qu untreated) increases from 6.5 to 14.3 at 15% settlement. However, when the water/cement ratio increases from 1.25 to 1.75, the ultimate bearing capacity ratio (qu treated/qu untreated) decreases from 14.3 to 11.4. The ultimate bearing capacity ratio improves with increasing curative time. It climbs from 14.3 to 19.6 during 3 to 28 days for cement grouting models, while the ultimate bearing capacity ratio grows from 6.5 to 7 during 3 to 28 days for heating process models only, at 15% settlement.
Highlights
This study examines the effect of time on strength and degree of improvement of grouting material in heated, cracked soil. The shear strength of the heated soil increased from 14 to 300 kPa At 15% settlement ratio, bearing ratio rose from 32.9 to 71.7 as water-cement ratio increased from 0 to 1.25 At 15% settlement, ultimate bearing capacity ratios decreased from 14.3 to 11.4 for models with 1.25 to 1.75 water-cement ratios At 15% settlement, bearing ratios for heating and 1.25 water-cement grouting were 71.70, 88.19 and 98 for different curing times
Keywords
Soft soil; Bearing capacity ratio; Grouting, Heating; Portland cement; Curing period

References
M. Tarsh, M. A. Al-Neami, and K. Y. H. Al-Soudany, Variation of Consistency Limits and Compaction Characteristics of Clayey Soil with Nanomaterials, J. Eng. Technol., 39 (2021) 1257–1264. https://doi.org/10.30684/etj.v39i8.1930 A. M. Al-Neami, Reducing settlement of soft soils using local materials, J. Eng. Technol., 28 (2010) 6649–6661. https://doi.org/10.30684/etj.28.23.4 M. Abu-Zreig, N. M. Al-Akhras, and M. F. Attom, “Influence of heat treatment on the behavior of clayey soils, Appl. Clay Sci., 20 (2001) 129–135. https://doi.org/10.1016/S0169-1317(01)00066-7 A. M. Al-Neami., F. H .Raheel, & Y. H. Al-Ani, Behavior of Cohesive Soil Reinforced by Polypropylene Fiber, J. Eng. Technol., 38 (2020) 801–812. http://dx.doi.org/10.30684/etj.v38i6A.109 Y.Fattah, M. M. Al-Ani, & M. T. A Al-Lamy, Studying collapse potential of gypseous soil treated by grouting, Soils Found., 54 (2014) 396–404. https://doi.org/10.1016/j.sandf.2014.04.008 N. Ibragimov, Characteristics of Soil Grouting by Hydro-Jet Technology, Soil Mech. Found. Eng., 50 (2013) 200-205. https://doi.org/10.1007/s11204-013-9234-8 H.Shareef, M. A. Al-Neami, & F. H. Rahil, Some of The Field and Laboratory Studies on Grouting Properties for Weak Soils: A Review. Int. J. Intell. Syst. Appl. Eng., 11 (2023) 131–141. Duan, Z. Jiang, S. Zhu, P. Yao, and Q. Sun, “New composite grouting materials: Modified urea–formaldehyde resin with cement, Int. J. Min. Sci. Technol., 22 (2012) 195–200. https://doi.org/10.1016/j.ijmst.2011.08.009 Faramarzi, A. Rasti, and S. M. Abtahi, “An experimental study of the effect of cement and chemical grouting on the improvement of the mechanical and hydraulic properties of alluvial formations, Constr. Build. Mater., 126 (2016) 32–43. https://doi.org/10.1016/j.conbuildmat.2016.09.006 Varol and S. Dalgıç, “Grouting applications in the Istanbul metro, Turkey. Tunnelling Underground Space Technol., 21 (2006) 602–612. https://doi.org/10.1016/j.tust.2005.11.002. El Tani, Grouting rock fractures with cement grout, Rock Mechanics and Rock Engineering, 45 (2012) 547–561. http://dx.doi.org/10.1007/s00603-012-0235-0 Funehag and G. Gustafson, Design of grouting with silica sol in hard rock–New methods for calculation of penetration length, Part I. Tunnelling Underground Space Technol., 23 (2008) 1–8. https://doi.org/10.1016/j.tust.2006.12.005 S. Liu, C. B. Lu, B. Liu, and X. L. Lu, Research on rheological behavior for cement grout considering temperature and hydration time effects, Chin. J. Rock Mech. Eng, 33 (2014) 3730–3740. http://dx.doi.org/10.13722/j.cnki.jrme.2014.s2.042 Zhong-Miao, Z. O. U. Jian, H. E. Jing-Yi, and W. Hua-qiang, Laboratory tests on compaction grouting and fracture grouting of clay, Chin. J. Geotech. Eng., 31(2009) 1818–1824. F. Huang, X. G. Li, X. Guo, and K. Atsushi, “Hydraulic fracture extending during slurry shield tunneling in cohesive soil,” Yantu Gongcheng Xuebao/ Chin. J. Geotech. Eng., 32 (2010) 712–717. M. Das, Principles of geotechnical engineering. Cengage learning, 2021.
Statistics Article View: 102 PDF Download: 103