Jaber, A., Mohammed, A., Younis, K. (2023). Improvement of Formability of AISI 1006 Sheets by Hydroforming with Die in Square Deep Drawing. Alustath, 41(12), 1488-1496. doi: 10.30684/etj.2023.141104.1482
Adil S. Jaber; Adnan I. Mohammed; Karem M. Younis. "Improvement of Formability of AISI 1006 Sheets by Hydroforming with Die in Square Deep Drawing". Alustath, 41, 12, 2023, 1488-1496. doi: 10.30684/etj.2023.141104.1482
Jaber, A., Mohammed, A., Younis, K. (2023). 'Improvement of Formability of AISI 1006 Sheets by Hydroforming with Die in Square Deep Drawing', Alustath, 41(12), pp. 1488-1496. doi: 10.30684/etj.2023.141104.1482
Jaber, A., Mohammed, A., Younis, K. Improvement of Formability of AISI 1006 Sheets by Hydroforming with Die in Square Deep Drawing. Alustath, 2023; 41(12): 1488-1496. doi: 10.30684/etj.2023.141104.1482

Improvement of Formability of AISI 1006 Sheets by Hydroforming with Die in Square Deep Drawing

Engineering and Technology Journal
Article 6, Volume 41, Issue 12, December 2023, Pages 1488-1496    PDF (1.19 M)
Document Type: Research Paper
DOI: 10.30684/etj.2023.141104.1482
Authors
Adil S. Jaber* ; Adnan I. Mohammed; Karem M. Younis
Production Engineering and Metallurgy Dept., University of Technology-Iraq, Alsina’a street, 10066 Baghdad, Iraq.
Abstract
An effort has been made to improve the formability of (1006) AISI steel alloy sheets in deep drawing of square-shaped parts with flat bases through hydroforming. To achieve this goal, the manufacturing process involved the use of a newly developed experimental setup for sheet hydroforming with a die, which was created by the researchers. The key design features of this setup aimed for simplicity and modularity, allowing for potential utilization with oil pressures of up to 100 MPa. The obtained results were compared with those of conventional deep drawing. Both processes were examined under specific conditions to form identical cups up to the full depth of the provided die. Indicators of formability considered for comparison included the minimum possible corner radius, the maximum achievable depth without failure, and the maximum percentage of thinning at the corners. This study demonstrates that hydroforming can enhance the formability of low-carbon steel alloy sheets by improving the flow of metal into the die cavity and reducing thinning at critical regions, when compared to conventional deep drawing processes. In conventional deep drawing, only 70% of the full depth could be achieved before failure due to high local deformations resulting in significantly higher thinning at the corners.

Highlights
  • A new hydroforming setup with a die was designed, made, and assembled.
  • The new setup enhances the formability of (1006) AISI steel in square deep drawing.
  • The hydroforming deep drawing was compared to the conventional one for cup forming.
  • Hydroforming enhances low-carbon steel formability by reducing thinning.
  • Conventional deep drawing only reaches 70% depth due to corner thinning.
Keywords
Hydroforming with die; Conventional forming Steel alloy; Thinning; Formability
References
  1. Modi and D. R. Kumar, Optimization of process parameters to enhance formability of AA 5182 alloy in deep drawing of square cups by hydroforming, J. Mech. Sci. Technol., 33 (2019) 5337–5346. https://doi.org/10.1007/s12206-019-1026-2
  2. Younis and A. Jaber, Metal Flow Control in Producing the Non Symmetrical Parts in Deep Drawing Process, Eng. Technol. J., 36 (2018) 603–611. https://doi.org/10.30684/etj.36.6a.2
  3. Muhson Younis, A. Shbeeb Jaber and A. Mahdi salah, Numerical Analysis of The Multi-Stage Reverse Deep Drawing Process, Eng. Technol. J., 34 (2016) 613–622. https://doi.org/10.30684/etj.34.3a.15
  4. H. Mohsein, W. K. Jawad and A. H. Abed, Experimental and Theoretical Analysis to Produce Pentagonal Cup in Deep Drawing Process, Eng. Technol. J., 41 (2023) 1–10. http://doi.org/10.30684/etj.2023.138865.1407
  5. J. Jweeg, A. I. mohammed and M. S. Jabbar, Investigation of Thickness Distribution Variation in Deep Drawing of Conical Steel Products, Eng. Technol. J., 39 (2021) 586–598. https://doi.org/10.30684/etj.v39i4a.1908
  6. -L. Xia, S.-H. Zhang, Y. Xu, S.-F. Chen, B. B. Khina and A. I. Pokrovsky, Deformation characteristics and inertial effect of complex aluminum alloy sheet part under impact hydroforming: experiments and numerical analysis, Adv. Manuf., 11 (2023) 311–328. https://doi.org/10.1007/s40436-022-00430-0
  7. Ghasemi, M. Elyasi, H. Baseri and M. J. Mirnia, Microstructural analysis of sheet hydroforming process assisted by radial ultrasonic punch vibration in a hydro-mechanical deep drawing die, Int. J. Adv. Manuf. Technol., 125 (2023) 5359-5368. https://doi.org/10.1007/s00170-023-11007-x
  8. Jebri, T. Lazghab, M. Toumi, and M. Soula, The behavior and forming performance of vapor hydroforming process of thin aluminum sheets: Numerical and experimental analysis, Adv. Mech. Eng., 14 (2022) 1–16. https://doi.org/10.1177/16878132221089380
  9. J. Liu, Z. H. Zhang, X. F. Ma, C. Li, and Y. Y. Zhou, Study on hydroforming of AA6061-T6 aluminum alloy sheet based on upper sheet, Int. J. Adv. Manuf. Technol., 123 (2022) 4447–4464. https://doi.org/10.22059/jcamech.2018.246043.209
  10. S. Halkaci, Manufacturing of Cups by Warm Hydroforming Process, Ecol. Technol., 1 (2016) 690–697.
  11. A. Ahamed J and P. Chinnaiyan, Studies on Finite Element Analysis in Hydroforming of Nimonic 90 Sheet, Mathematics, 11 (2023) 1–15. https://doi.org/10.3390/math11112437
  12. Yaghoubi, F. F. Saniee, An Investigation on the Effects of Optimum Forming Parameters in Hydro-mechanical Deep Drawing Process Using the Genetic Algorithm, JCAMECH, 49 (2018) 54-62. https://doi.org/10.22059/jcamech.2018.246043.209
  13. T. Hama, K. Kurisu, K. Matsushima, H. Fujimoto and H. Takuda, Outflow characteristics of a pressure medium during square- Cup sheet hydroforming, 9th Int. Conf. Technol. Plast. ICTP 2008, 2008, 230-231.
  14. T. Thu and N. D. Trung, Effect of technological and geometrical parameters on formation of radius region at cylindrical product bottom in hydrostatic forming, J. Korean Soc. Precis. Eng., 36 (2019) 891–900. https://doi.org/10.7736/KSPE.2019.36.9.891
  15. Eladl, O. B. Abouelatta, M. Samuel and T. A. Enab, Effect of Hydroforming Drawing Cups on Thickness Variation and Surface Roughness, Int. J. Eng. Res. Africa, 59 (2022) 1–18. https://doi.org/10.4028/p-ki740n
  16. Forouhandeh, A Comparison Between Two Methods of Sheet Hydroforming By Simulation, Evol. Mech. Eng., 2 (2018) 4–7. https://doi.org/10.31031/EME.2018.02.000534
  17. A. Zahedi, H. Goodarzian, M. Okazi, and M. Bakhshi-Jooybari, Investigation of conventional deep drawing and hydroforming deep drawing via experimental and finite element simulation, Indian J. Sci. Technol., 3 (2010) 1009–1013. https://doi.org/10.17485/ijst/2010/v3i9/29878
  18. Abbadeni, I. Zidane, H. Zahloul, and Z. Madaoui, Comparative study of conventional and hydromechanical deep drawing processes based on finite element analysis, Frat. ed Integrita Strutt., 13 (2019) 282–290. https://doi.org/10.3221/IGF-ESIS.49.28
  19. T. Feyissa and D. R. Kumar, Enhancement of drawability of cryorolled AA5083 alloy sheets by hydroforming, J. Mater. Res. Technol., 8 (2019) 411–423. https://doi.org/10.1016/j.jmrt.2018.02.012
  20. Vukota B., Sheet Metal Forming Processes and Die Design, Ind. Press Inc., p. 240, 2004.
  21. T. Nguyen and T. D. Nguyen, On the High Fluid Pressure in Hydrostatic Forming for Sheet Metal, Int. J. Precis. Eng. Manuf., 21 (2020) 2223–2233. https://doi.org/10.1007/s12541-020-00426-5
Statistics
Article View: 216
PDF Download: 244


Journal Management System. Powered by ejournalplus.com