Effect of Machining Parameters on Surface Roughness and Metal Removal Rate for AISI 310 L Stainless Steel in WEDM | ||
| Engineering and Technology Journal | ||
| Article 21, Volume 40, Issue 1, January 2022, Pages 181-188 PDF (576.82 K) | ||
| DOI: 10.30684/etj.v40i1.2060 | ||
| Authors | ||
| Muayad M. Ali* ; Abbas F. Ibrahim | ||
| Production Engineering and Metallurgy Dept., University of Technology-Iraq, Alsina’a street, 10066 Baghdad, Iraq. | ||
| Abstract | ||
| Wire electrical discharge machining (WEDM) is a non-traditional machining process that is widely used in the machining of conductive materials. This paper presents the investigation on surface roughness and metal removal rate of stainless steel using the wire-cut EDM process. Process input parameters wire feed (WF), wire tension (WT), servo voltage (SV), pulse on time (TON) and pulse off time (Tuff), and the output parameters surface roughness and metal removal rate. The work piece material was used stainless steel 310 L, zinc-coated brass wire of 0.25mm diameter used as a tool and distilled water is used as dielectric fluid. ANOVA used to measure and evaluate the relative importance of different factors. Experiments are designed and analyzed using the factorial design approach. The experimental results revealed that the most important machining parameter of the pulse of time has the most influence on the metal removal rate and the surface roughness. The maximum best metal removal rate is (0.052277 g/min). When the values are somewhat medium range, they are the best and the wire does not break at this range. Wire feed (7m/min), wire tension (7 kef), servo voltage (30 V), TON (30 sic), Tuff (30 sic). The expected values and measured values are well-matched as observed by additional confirmation experiments. | ||
Highlights | ||
| ||
| Keywords | ||
| Metal removal rate; Analysis of variance (ANOVA); Pulse on time (TON); Pulse off time (Tuff); Servo voltage (SV); Wire tension (WT) | ||
| Full Text | ||
|
· The used program Minitab 17. The workpiece material was used stainless steel 310 L · zinc coated brass wire of 0.25mm diameter used as a tool · Process input parameters wire feed, wire tension, servo voltage, TON and Toff. · The output parameters surface roughness and metal removal rate. Experiments are designed and analyzed using the factorial design approach. | ||
| References | ||
|
[1] R. Bhatia, and S. Kumar, Experimental Analysis of Surface Roughness for Heat Treated H-11 Die Steel by WEDM, International Journal of Research in Mechanical Engineering & Technology, 3 (2013) 109-111. [2] V. Kumar, A. K. Yadav,and I. Singh, A review on current research trends in wire-electrical discharge machining (WEDM), International Journal of science technology and management, 5 (2016) 103- 112. [3] S.K. Shather and D.A. Noori, Influence of Intervening Variables on Surface Roughness and Metal Removal Rate during WEDM Process, Engineering & Technology Journal, 32 (2014) 1141-1148. [4] J.T. Huang, Y.S. Liao and Y.H. Chen, A Study to Achieve a Fine Surface Finish in Wire-EDM, Journal of Materials Processing Technology, 149 (2004) 165-171. [5] S. A. El-Bahloul, Optimization of wire electrical discharge machining using statistical methods coupled with artificial intelligence techniques and soft computing, SN Appl. Sci., 2 (2020). [6] M. Gostimirovic, P. Kovac, B. Skoric, and M. Sekulic, Effect of electrical pulse parameters on the machining performance in EDM, Indian J. Eng. Mater. Sci., 18 (2011) 411–415. [7] B. Azhiri, R. Teimouri, M. Ghasemi Baboly, and Z. Leseman, Application of Taguchi, ANFIS and grey relational analysis for studying, modeling and optimization of wire EDM process while using gaseous media, Int. J. Adv. Manuf. Technol., 71 (2014) 279–295. [8] K. Hinkelmann and O. Kempthorne, Design and Analysis of Experiments: Second Edition, Design and Analysis of Experiments: Second Edition, 1 (2009) 1–641. [9] D. Scott, S. Boyina, and K. P. Rajurkar, Analysis and optimization of parameter combinations in wire electrical discharge machining, Int. J. Prod. Res., 29 (1991) 2189–2207. [10] B. Kuriachen, J. Paul, and J. Mathew, Modeling of Wire Electrical Discharge Machining Parameters Using Titanium Alloy (Ti-6AL-4V), Int. J. Emerg. Technol. Adv. Eng., 2 (2012) 377–381. [11] D. Sudhakara and G. Prasanthi, Application of touchy method for determining optimum surface roughness in wire electric discharge machining of P/M cold worked tool steel (Vanadis-4E), Procardia Eng., 97 (2014) 1565–1576. [12] J. Singh, Review on Effects of Process Parameters in Wire Cut EDM and Wire Electrode Development, 2 (2016) 701–706. [13] B. K. Lodhi, S. Agarwal, and S. Ahamad, Metals Today : Proceedings Optimization of WEDM parameters on surface roughness of EN41B steel, Mater. Today Proc., (2019) 0–4. [14] S.H.Tomadi, M.A.Hassan, Z. Hamedon, IAENGR.Daud and A.G.Khalid, Analysis of the Influence of EDM Parameters on Surface Quality, Material Removal Rate and Electrode Wear of Tungsten Carbide, Proceedings of the International Multi Conference of Engineers and Computer Scientists, 2 (2009) 978-988. | ||
|
Statistics Article View: 307 PDF Download: 268 |
||