Size Effect on The Shear Strength of Reinforced Concrete Beams

Jaber, Hind T.; Sarsam, Kaiss F.; Muhammad, Bassman R.

doi:10.30684/etj.v39i12.2283

	Size Effect on The Shear Strength of Reinforced Concrete Beams
Engineering and Technology Journal
Article 27, Volume 39, Issue 12, December 2021, Pages 1960-1976 PDF (1.43 M)
DOI: 10.30684/etj.v39i12.2283
Authors
Hind T. Jaber^* ; Kaiss F. Sarsam; Bassman R. Muhammad
Civil Engineering Dept., University of Technology-Iraq, Alsina’a street, 10066 Baghdad, Iraq.
Abstract
According to research, as the depth of a beam increases, the section's shear strength can be expected to decrease. The size effect is a phrase that has been used to describe this tendency. Testing of unreinforced specimens under shear has also shown that the shear strength might be lower than what is typically anticipated in the design. As a result, it is critical to comprehend the behavior of these structures, as they may be influenced by a size impact. Sixteen reinforced concrete beams of different rectangular cross-sections without stirrups were tested. The tested beams were simply supported made of high-strength reinforced concrete subjected to two equal concentrated loads up to the failure. The experimental results showed that all of the beam specimens failed in shear except one which had failed by flexure. Moreover, increasing beam height from 150 to 250 mm has decreased the cracking and ultimate shear strength ratio for all groups except for group four when the beam height increased from 150 to 300 mm the cracking and ultimate shear strength ratio has increased. Furthermore, increasing beam depth from 150mm to 300mm has led to increasing the ultimate load besides decreasing their final deflection at the same level of load, which is the apparent size effect in the stiffness of the tested beams.
Highlights
Increasing beam cross-section size from (75x150) mm to (150x300) mm has decreased the ultimate shear stress with different ratios. The percentage of decrease was 8, 12 for concrete compressive strength of 45MPa and tensile steel reinforcement ratio of (ρ/ρb = 0.18). The percentage of decrease was 9, 7 and 9 for concrete compressive strength of 65MPa and tensile steel reinforcement ratio of (ρ/ρb = 0.18).
Keywords
Cracking; deflection; High Strength Concrete; Shear Strength; Slender Beams; size effect

References
[1] P.-C. Aïtcin, High-Performance Concrete E & FN SPON. (2004). [2] [E. C. P. ASBL, Commentary Eurocode 2. European Concrete Platform ASBL, (2008). [3] S. Cholostiakow, M. Di Benedetti, K. Pilakoutas, and M. Guadagnini, Effect of beam depth on shear behavior of FRP RC beams, J. Compos. Constr., 23 (2018). 40. [4] D. Y. Yoo and J. M. Yang, Effects of stirrup, steel fiber, and beam size on shear behavior of high-strength concrete beams, Cem. Concr. Compos., 87 (2018) 137–148. [5] J.-Y. Lee, J.-H. Lee, D. H. Lee, S.-J. Hong, and H.-Y. Kim, Practicability of large-scale reinforced concrete beams using grade 80 stirrups, ACI Struct. J., 115 (2018) 269–280. [6] A. Althin and M. Lippe, Size effects in shear force design of concrete beams, MSc Thesis,Division Struct. Eng. Fac. Eng. LTH,Sweden, p. 70, (2018). [7] D. I. Shin, M. Haroon, C. Kim, B. S. Lee, and J. Y. Lee, Shear strength reduction of large-scale reinforced concrete beams with high-strength stirrups, ACI Struct. J., 116 (2019) 161–172. [8] G. B. Jumaa and A. R. Yousif, Size effect in shear failure of high strength concrete beams without stirrup reinforced with basalt FRP bars, KSCE J. Civ. Eng., 23 (2019) 1636–1650. [9] T. Wu, H. Wei, and X. Liu, Shear behavior of large-scale deep beams with lightweight-aggregate concrete, ACI Struct. J., 117 (2020) 75–89. [10] S. H. Chao, Size effect on ultimate shear strength of steel fiber-reinforced concrete slender beams, ACI Struct. J., 117, no. 1 (2020) 145–158. [11] No. 5/1984, Iraqi Specification, Portland Cement. Ministry of Planning, Central Agency for Standardization and Quality Control, (1984). [12] H. P. J. Taylor, “Shear strength of large beams,” J. Struct. Div. ASCE, 98 (1972) 2473–2489. [13] ASTM C-494/C 494M, Standard specification for chemical admixtures for concrete. (2001). [14] ASTM C 1240 – 05, Standard specification for silica fume used in cementitious mixtures. (2005). [15] ASTM A615-16, Standard specification for deformed and plain carbon structural steel bars for concrete reinforcement. Annual Book of ASTM Standards,( 2016). [16] ASTM C 39/C 39M – 03, Standard test method for compressive strength of cylindrical concrete specimens. (2003). [17] ACI 318M-19, Building code requirements for structural concrete and commentary. (2019). [18] ASTM C 192/C 192M-05, Standard practice for making and curing concrete test specimens in the laboratory. Annual Book of ASTM Standards, (2005). [19] TML Company, Strain gauges user guide, No Title, Tokyo Sokki Kenkyujo Co., Ltd, Japan, Web site www.tml.jp/e. [20] L. H. Sneed and J. A. Ramirez, Influence of effective depth on shear strength of concrete beams-experimental study, ACI Struct. J., 107 (2010) 554–562. [21] Z. P. Bazant and M. T. Kazemi, Size effect on diagonal shear failure of beams without stirrups, ACI Struct. J., 88 (1991) 268–276. [22] P. Bazant, Z. P.; Kim, J. K.; and Pfeiffer, Determination of nonlinear fracture parameters from size effect tests. (1984). [23] ACI-ASCE Committee 445R, Recent approaches to shear design of strucutral concrete, ACI, p. 55, (1999). [24] Shioya et al., “Shear strength of large reinforced concrete beams,” ACI Struct. J., 118 (1990) 259–280. [25] D. Collins, M. P., and Mitchell, Prestressed concrete structures. Response Publications, Canada, (1997). [26] T. Sherwood and A. Lubell, Safe shear design of large, wide beams adding shear reinforcement is recommended, Concr. Int. Des. Constr., (2004) 66–78. [27] ASCE-ACI Committee 426, The shear strength of reinforced concrete members, J. Struct. Div., 99 (1973) 1091–1187.
Statistics Article View: 293 PDF Download: 301