Influence of Polarity of Electro Discharge Machine (EDM) on Surface Roughness (SR) and Metal Removal Rate (MRR) of Low Carbon Steel | ||
| Engineering and Technology Journal | ||
| Article 4, Volume 38, 7A, July 2020, Pages 975-983 PDF (1.04 M) | ||
| DOI: 10.30684/etj.v38i7A.469 | ||
| Authors | ||
| Shahd Taqi* 1; Saad K. Shather2 | ||
| 1Production Engineering and Metallurgy Department., Baghdad, Iraq | ||
| 2Production engineering and metallurgy department, university of technology, Baghdad, Iraq. | ||
| Abstract | ||
| Electro discharge machining (EDM) is one of a thermal process that is used for remove of metal from the workpiece by spark erosion. The work of this machine depends on multiple variables. One of the more influential variants on this machine is the change of polarity and the use of this variable is not wide and the research depends on the polarity of the machinist. Essentially, the polarity of the tool (electrode) is positive and the workpiece is negative, this polarity can be reversed. This paper focuses on the influence of changing the polarity (positive and negative) on the surface roughness and metal removal rate by using different parameters (current, voltages, polarity and Ton). Experiments show that the positive electrode gives (best surface roughness = 1.56 μm when the current = 5 Am and Ton = 5.5 μs) and (best metal removal rate = 0.0180 g/min when the current = 8 Am and Ton = 25 μs). Negative electrode gives (best surface roughness = 0.46 μm when the current = 5 Am and Ton = 5.5 μs) and (best metal removal rate = 0.00291 g/min when the current = 8 Am and Ton = 25 μs). | ||
| Keywords | ||
| EDM; Polarity; MRR; Surface roughness (Ra) | ||
| References | ||
|
[1] K. D. Ahmad, and M. Hameedullah, “Effect of tool polarity on the machining characteristics in electric discharge machining of silver steel and statistical modelling of the process,” International Journal of Engineering Science and Technology 3, no. 6, 2011. [2] J. Pichai, and A. Muttamara, “Performance of difference electrode materials in electrical discharge machining of tungsten carbide,” Energy Research Journal 1, no. 2, 87-90, 2010. [3] F. L. Amorim, and W. L. Weingaertner, “The behavior of graphite and copper electrodes on the finish die-sinking electrical discharge machining (EDM) of AISI P20 tool steel,” Journal of the Brazilian Society of Mechanical Sciences and Engineering 29, no. 4, 366-371, 2007. [4] A. Shaaz, “Current research trends in electric discharge machining (EDM),” International Journal of Scientific & Engineering Research 5, 100-118, 2014. [5] O. H. Bekir, “Effect of changing polarity of graphite tool/hadfield steel workpiece couple on machining performances in die sinking EDM,” In MATEC Web of Conferences, vol. 129, p. 01034. EDP Sciences, 2017. [6] M. S. Reza, M. A. Azmir, S. H. Tomadi, M. A. Hassan, and R. Daud, “Effects of polarity parameter on machining of tool steel workpiece using electrical discharge machining,” In Proceedings of the National Conference in Mechanical Engineering Research and Postgraduate Students, Kuantan, Pahang, Malaysia, pp. 26-27. 2010. [7] S. K. Shather, “Improving the metal removal rate (MRR) in electro discharge machining by additives powder,” Engineering and Technology Journal 34, no. 14 Part (A) Engineering, 2766-2774, 2016. [8] A Begum,. and D. R. Reddy, “Effect of polarity on the machining characteristics and surface generation in EDM,” Materials Today: Proceedings 4, no. 8, 7674-7679, 2017. [9] H. P. Schulze, “Importance of polarity change in the electrical discharge machining,” In AIP Conference Proceedings, Vol. 1896, No. 1, p. 050001. AIP Publishing, 2017. | ||
|
Statistics Article View: 277 PDF Download: 260 |
||