Studying The Effect of a New Mixed Cutting Fluid on Surface Roughness | ||
| Engineering and Technology Journal | ||
| Article 3, Volume 38, 11A, November 2020, Pages 1593-1601 PDF (1.19 M) | ||
| Document Type: Research Paper | ||
| DOI: 10.30684/etj.v38i11A.1516 | ||
| Authors | ||
| Mohammed H. Shaker* 1; Salah K. Jawad1; Maan A. Tawfiq2 | ||
| 1Production Engineering and Metallurgy Dept. Baghdad, Iraq, | ||
| 2Production Engineering and Metallurgy Department, University of Technology Baghdad, Iraq | ||
| Abstract | ||
| This research studied the influence of cutting fluids and cutting parameters on the surface roughness for stainless steel worked by turning machine in dry and wet cutting cases. The work was done with different cutting speeds, and feed rates with a fixed depth of cutting. During the machining process, heat was generated and effects of higher surface roughness of work material. In this study, the effects of some cutting fluids, and dry cutting on surface roughness have been examined in turning of AISI316 stainless steel material. Sodium Lauryl Ether Sulfate (SLES) instead of other soluble oils has been used and compared to dry machining processes. Experiments have been performed at four cutting speeds (60, 95, 155, 240) m/min, feed rates (0.065, 0.08, 0.096, 0.114) mm/rev. and constant depth of cut (0.5) mm. The amount of decrease in Ra after the used suggested mixture arrived at (0.21μm), while Ra exceeded (1μm) in case of soluble oils This means the suggested mixture gave the best results of lubricating properties than other cases. | ||
| Keywords | ||
| Surface Roughness; Turning; Cutting Fluids; Soluble Oil | ||
| References | ||
|
1] K. Prasad and S. Chakraborty, “A Quality function deployment-based model for cutting fluid selection,” Advances in Tribology (1), pp. 1-10, 2016. [2] F. Klocke, and G. Eisenblatter, “Dry cutting,” Annals of CIRP, Vol. 46(20), pp. 519-526, 1997. [3] S. Ebbrell, N.H. Woolley, Y.D. Trimidas, and D.R. Allanson, W.B. Rowe, “The Effects of cutting fluid application methods on the grinding process,” International Journal of Machine Tools and Manufacture, Vol 40, 209-223, 2000. [4] Y. Liu, A. Wang, B. Wang, and Z. Liu, “Experimental study on the effects of oil/water emulsion on machining stainless steel,” International Technology and Innovation Conference, pp. 1-4, 2009. [5] A. I. Obi, A.A. Alabi, R. B.O. Suleiman, and F.O. Anafi “Verification of some vegetable oils as cutting fluid for Aluminum,” Nigerian Journal of Technological Development, December, 2013. [6] S. G. Hussein “An Experimental study of the effects of coolant fluid on surface roughness in turning operation for brass alloy,” Journal of Engineering, March, 2014. [7] P.J. Liew, A. Shaaroni, N.A.C. Sidik, J. Yan, “An overview of current status of cutting fluids and cooling techniques of turning hard steel,” International Journal of Heat and Mass Transfer 114, pp. 380–394, 2017. [8] Z. Wank, “The Correlation between the penetration force of cutting fluid and machining stability,” A Thesis of the Degree of Master of Science, Worcester Polytechnic Institute, May, 2010. [9] M.A. El Baradie, “Cutting fluids Part I: Characterization,” Journal of Materials Processing Technology 56, pp. 786-797, 1996. | ||
|
Statistics Article View: 210 PDF Download: 168 |
||